GTA Aquarium Forums banner

90 Gallon Custom

36K views 197 replies 22 participants last post by  hendy8888 
#1 · (Edited)
It's been a while since I tore down my 5ft planted. I always had intentions of doing another build but life got in the way and I have been slowly turning my plans into reality.

I enjoy documenting the progress of each build so I can easily see the tanks progression and have decided to play a little catch up.

Spring 2015

It started with a custom 48"x24"x18" rimless low iron tank ordered from Krakens Reef. It was a long time coming and got rejected by customs the first time because of wood shipping material.



Very impressed with the craftsmanship.



 
See less See more
3
#4 ·
September 2016
Bottom and top glued on

Outer part of the stand is made of 3/4" MDO.







Ripping an angle used to open the top of the doors. Having a right tilt table saw made it a challenge to do this safely without binding. Creating a sacrificial fence to bury the blade in and create an opening for the off cut worked very well.





Making a face frame without any joints. I just used a jigsaw with a straight edge for the final cut to get 90 degree corners.



Sent from my LG-H933 using Tapatalk
 
#5 ·
I chose soss hinges due to the 180 degree opening and being able to inset mount the doors. I looked for an euro hinge that would mount but came up empty without adding addition support to mount them.

Instead of buying an expensive jig I set my own up using clamps and a straight edge.


This had to be done to the face frame before I attached it to the stand.


Not that bad for a cheap router and plywood edges.



Next I flush trimmed the top of the stand


Test fit of face frame and doors with hinges installed before I glued it together.
 
#9 ·
October 2016

Glued the face frame on and mounted the doors.







Quick test fit of the 20lbs CO2 tank with reg. Pretty snug...



Nowhere near enough long clamps so anything in sight went on top during the glue up of the remaining 3 sides....I bet those blankets really helped out alot...



Success! Fairly difficult glue up since all the seams were 45 degrees to get the seamless finish.

 
#10 ·
November 2016

Flush trimmed the top, bottom, and corners of the stand. The MDO was pretty hard on the router bits.





Got to love plywood chip out..



Easy way to drill some angled holes for a light bar across the inside of the stand.





Major construction pretty much done aside from a few openings.





January 2017

Hole on the back for power cords, didn't take any pictures of the large side hole for plumbing.





Did I mention the cheap router..one bit wasn't so flush cut as it should be. Probably almost a 1/8" more than flush so it got filled in with Bondo.



Soss hinges don't have self closing (that fit at least) so I used rare earth magnets.





Needed more attraction so stepped it up a bunch and added some soft close bumpers.

 
#11 ·
The stand sat in the garage for over a year while I procrastinated over finishing it. Between work and winter weather I always seemed to miss my window to paint. I did get the bondo work done to all the seams and exposed plywood edges to seal them up.

April 2018

Tried a black limo tint for the background, went on very nice and was initially happy.









This is my first time spraying a finish and probably why it took me so long to pull the trigger.

I took apart my Sfiligoi stealth t5 to upgrade the paint as well.




Cheap $10 Harbour Freight paint gun to learn on and 3 coats of Cover Stain.



Once the primer was on I found some cracks from the wood warping a tiny bit (was left in a garage after all). Fixed with some baking soda grinded into the crack and then flowed in some thin crazy glue followed by another sanding.



So far so good


Better look at the plumbing access.
 
#12 ·
May 2018

I decided to test the black limo tint with a light overhead. The light fixture I'm using is the same size as the tank so there will be over spill.


Not impressed with the limo tint anymore...


So it had to go


Replaced it with black vinyl.


Much better


June 2018

Makeshift paint setup


Top coat


That furniture dolly was worth it's weight in gold..




Wet sanding between coats.


3 Coats later




All done and moved inside, I couldn't be happier.


 
#15 ·
July 2018

A better look at the interior lights. There is a sensor on the right door that makes the lights come on when you open the door and go off when you close it.










Standard RGB light strip, so pick a colour.


Yoga mat for under the tank


Tank and stand together


All caught up now so the updates will roll in slowly from here on.
 
#16 ·
RKL is mounted.


Plumbing almost finished, just need to glue a couple joints. Going with a Herbie drain but is designed to make it Bean Animal very easily if I need to.




Waiting on some SCS 1200 silicone in clear to get in stock so I can finish the sump off and seal the bottom of the stand to ensure its water tight. After that I will water test.
 
#17 ·
Got the light finished and mounted. I needed a new hanging kit since the old wires were rusted. The wires that attach to the light in the ATI kit I'm using ended up being to short so I had to make my own.

How the cable stop starts out


How it ends up with a little trimming and sanding.


A shot showing how Sfiligoi attaches the cables. Just a slot for a washer to slide down.


Holds so far, I was hoping to find a stud but no luck. I didn't want an ugly washer at the ceiling which is required when using the toggle bolts so I used snap toggles. Very similar but allowed a slightly smaller hole so no washer required.










I'm happy with how the light turned out, I am still undecided if I want to rewire what 4 bulbs are on each power cord. They currently alternate dual bulb sets but I might make the centre 4 on one cord and the outer 4 on another. I will mostly only use 4 bulbs with a short burst of 8.
 
#21 ·
Thanks, the vinyl I got off Aliexpress and it comes in a roll. Clean the glass well with Isopropyl alcohol and then spray the glass with water. Cut the vinyl to the correct size with a little extra overhang. Peel the backing off the vinyl to expose its sticky side and spray it with water too. Lay it on the glass where you want it (the water lets it move around fairly easily) and then use a credit card or similar item to squeeze out all the water and bubbles till its flat. Once the water dries it will be stuck on and you can use a new razor blade to trim along the edge of the glass to get the perfect fit.

It peels off with effort, not very hard to get off but you will be surprised how much grip it has. I called a few sign shops and there vinyl was priced way too high for me. I think I paid $9 USD for 50cm x 152cm on Aliexpess if you can wait a month for shipping.
 
#20 ·
noiceeee

very nice looking , love how this has come togeather
 
#23 ·
documenting

keep documenting , theres still some hard core people on here who are lurking

were not all looking for kijjii deals
 
#25 ·
Awesome build so far! Just picked up a 50 gal/30 gallon sump setup that we're planning to plant out. Got it cleaned, stand painted & plumbed over the last week. Leak testing still to come...🤞🏻

Sent from my iPhone using Tapatalk
Sounds like a better schedule than I ended up having. This is my first sump and plumbing, had a couple drips on all 6 of my threaded pvc joints but I didn't use a sealant. Lucky my plumbing all comes apart easy.
 
#28 ·
Sump modifications, for anyone interested SCS1200 silicone will bond acrylic to glass quite well.
Made a hole to hold the heater in a perfect spot, room for 2 heaters if I want as well.


Drip plates, don't mind the yellow water.


Squeezed that 20lb co2 tank and reg in there..glad my planning is paying off when I designed the stand.


Some filter media in there, still need more but mise we'll start the cycle even though the main display is empty getting hardscaped. Love that I can recirculate the filter while I do trimmings and tank cleaning.
 
#32 ·
Added some small black lava rock rubble for the base layer. I needed the extra height and I figured it might be like a knock off ADA power sand (No clue if it's beneficial).


Base layer of Tropica plant soil


Initial rock layout, no plan going in except I wanted two hills. I actually like it for a first attempt and no experience. Let me know if you would do any changes.




White balance issues in auto mode I think (same lighting)
 
#35 ·
Thanks, I always enjoy seeing your planted tank threads. I think it's going to be a mix of stems and carpet plants. I don't really have a desire to do a nature scape right now. I haven't had a planted tank for a few years so lots of newer plants I would like to try. I am thinking of stems in the back peaks running down the streets I have made that turn into carpeting plants. I am on the fence with HC though...I have always wanted to try it but I really don't want the up keep on a large area of it.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top